AiRTX Accessories
Aluminum Extensions We Provide Complete Solutions
No system is complete without the proper accessories. We provide all of the hoses, connectors, filters, etc. that you need to build a custom setup with AiRTX products.
Compressed Air Supply
Air supplies are plagued with condensed water vapor in the air lines. This condensation leads to rust and dirt in the air lines. Also, some compressors will allow oil or vapor to enter the line. Small orifices in the AiRTX Air Saver products may become clogged with the rust, dirt, and water droplets. A 5-micron filter will separate 99% of the foreign material from the air supply allowing virtually maintenance-free operation. The use of an oil filter will remove the oil droplets with an effective filtration of 0.01 ppm for an even cleaner air supply.
Air Filter Model 90175 can be used with all AiRTX products up to the Air Knives not longer than 12". Model 90180 can be used for the Air Knife 12" and longer.
The Oil Filter Model 91175 can be used along with the 90175 Air Filter for the same AiRTX products.
Keep in mind that the current line or air might contain dirt or oil and should be blown out before installation. Also, pipe thread sealant or tape must be carefully applied to avoid clogging product orifices.
| Model | Description | Price | |
|---|---|---|---|
| 23000 | Cold End Muffler | $40 | 
|
| 23008 | Cold End Muffler for Model 20008 | $35 |
|
| 23001 | Hot End Muffler | $20 |
|
| 23009 | Hot End Muffler for Model 20008 | $30 |
|
| 24010 | (H) Generator only 10 CFM for Maximum Cooling (Yellow) | $6 |
|
| 24011 | (L) Generator only 10 CFM for Maximum Low Temperature (Green) | $6 |
|
| 24015 | (H) Generator only 15 CFM for Maximum Cooling (Red) | $6 |
|
| 24016 | (L) Generator only 15 CFM for Maximum Cold Temperature (White) | $6 |
|
| 24025 | (H) Generator only 25 CFM for Maximum Cooling (Blue) | $6 |
|
| 24026 | (L) Generator only 25 CFM for Maximum Cold Temperature (Gray) | $6 |
|
| 24035 | (H) Generator only 35 CFM for Maximum Cooling (Brown) | $6 |
|
| 24036 | (L) Generator only 35 CFM for Maximum Cold Temperature (Taupe) | $6 |
|
| 24400 | Generator Kit Containing All Eight Generators: 10 thru 35 CFM for both Maximum Cooling and Cold Temperature | $47 |
|
| Aluminum Extensions For Blow Guns | |||
| A06 | 6 in. | $10 |
|
| A12 | 12 in. | $12 |
|
| A18 | 18 in. | $13 |
|
| A24 | 24 in. | $14 |
|
| A36 | 36 in. | $16 |
|
| A48 | 48 in. | $19 |
|
| HoleVac | |||
| 90420 | Deep Hole Cleaning Gun | $80 |
|
| Air Filters | |||
| 90175 | 1/4 in. Inlet, 75 CFM, 5 Micron, Auto Drain | $73 |
|
| 90180 | 1/2 in. Inlet, 170 CFM, 5 Micron, Auto Drain | $115 |
|
| 90185 | 3/4 in. Inlet, 140 CFM, 5 Micron, Auto Drain | $185 |
|
| 90190 | 1/4 in. Inlet, 75 CFM, 5 Micron, Manual Drain | $60 |
|
| 90200 | 1/2 in. Inlet, 170 CFM, 5 Micron, Manual Drain | $85 |
|
| Air Filters/Regulator Combination | |||
| 90215 | 3/4 in. Inlet, 140 CFM, 5 Micron w/ Gauge, Manual Drain | $255 |
|
| 90220 | 1/2 in. Inlet, 170 CFM, 5 Micron w/ Gauge, Automatic Drain | $160 |
|
| 90225 | 1/2 in. Inlet, 170 CFM, 5 Micron w/ Gauge, Manual Drain | $135 |
|
| 90230 | 1/4 in. Inlet, 75 CFM, 5 Micron w/ Gauge, Manual Drain | $94 |
|
| 90235 | 1/4 in. Inlet, 75 CFM, 5 Micron w/ Gauge, Automatic Drain | $114 |
|
| 90240 | 1/8 in. Inlet, 70 CFM, 5 Micron w/ Gauge, Manual Drain | $90 |
|
| Filter - Oil Coalescing, 0.01 Ppm Auto Drain | |||
| 91173 | 3/8 in. Inlet, 34 CFM | $205 |
|
| 91174 | 1/2 in. Inlet, 60 CFM | $230 |
|
| 91175 | 3/4 in. Inlet, 100 CFM | $255 |
|
| 91176 | 1 in. Inlet, 125 CFM | $310 |
|
| Regulators w/ Pressure Gauge | |||
| 90280 | 1/2 in. NPT Inlet, 170 CFM | $91 |
|
| 90285 | 1/4 in. Pressure Gauge, Back Connector, 2 in. Dial | $20 |
|
| Thermostat | |||
| 90300 | Preset At 90F (32C) | $85 |
|
| 90300-1 | Adjustable Thermostat, Preset at 90F | $160 |
|
| Solenoid Valves | |||
| 90301 | 1/4 in. Inlet, Normally Closed 35 CFM, 110V AC | $70 |
|
| 90301-1 | 1/4 in. Inlet, Normally Closed 35 CFM, 220V AC | $90 |
|
| 90302 | 3/8 in. Inlet, Normally Closed 75 CFM, 110V AC | $110 |
|
| 90302-1 | 3/8 in. Inlet, Normally Closed 75 CFM, 220V AC | $130 |
|
| 90303 | 1/2 in. Inlet, Normally Closed 100 CFM, 110V AC | $115 |
|
| 90303-1 | 1/2 in. Inlet, Normally Closed 100 CFM, 220V AC | $135 |
|
| 90301-6 | 1/4 in. Inlet, Normally Closed 35 CFM, 24V DC | $120 |
|
| 90302-6 | 3/8 in. Inlet, Normally Closed 75 CFM, 24V DC | $140 |
|
| 90303-6 | 1/2 in. Inlet, Normally Closed 100 CFM, 24V DC | $160 |
|
| 90303-7 | 1/2 in. Inlet, Normally Closed 35 CFM, 120V DC | $130 |
|
| 90301-9 | 1/4 in. Inlet, Normally Closed 35 CFM, Explosion Proof 110V AC | $120 |
|
| Snap Flex Hose | |||
| 90602 | 1/4 in. x 12 in. | $8.85 |
|
| 90603 | 1/4 in. Round Nozzle | $2.05 |
|
| 90604 | 1/4 in. x 1 in. Wide Flare Jet | $4 |
|
| 90606 | 1/4 in. Y Junction | $3.95 |
|
| 90607 | 1/4 in. Male Connector | $1.6 |
|
| 90608 | 1/2 in. X 12 in. Snap Flex Hose | $11.5 |
|
| 90609 | 1/2 in. Round Nozzle | $2.85 |
|
| 90610 | 1/2 in. X 1 1/4 in. Wide Flare Jet | $4.2 |
|
| 90611 | 1/2 in. x 2 1/2 in. Wide Flare Jet | $5.2 |
|
| 90612 | 1/2 in. Y Junction | $5.2 |
|
| 90613 | 1/2 in. Male Connector | $3 |
|
| 90614 | 1/2 in. x 1/4 in. Y Reducer | $4 |
|
| 90615 | 1/4 in. Assembly Hand Tool | $15 |
|
| 90616 | 1/2 in. Assembly Hand Tool | $15 |
|
| 90620 | 1/2 in. Nozzle For Stainless Airgun Model #60015, 60051 | $12.5 |
|
| 90601 | 1/2 in. Connector With 1/4 in. Dual Point Hose and Nozzles | $22 |
|
| 90601-1 | 3/8 in. Connector With 1/4 in. Dual Point Hose and Nozzles | $22 |
|